Install on CentOS/Red Hat with yum

This page describes the recommended instructions for installing the latest stable version of rippled on CentOS 7 or Red Hat Enterprise Linux 7, using Ripple's yum repository.

These instructions install a binary that has been compiled by Ripple.

Prerequisites

Before you install rippled, you must meet the System Requirements.

Installation Steps

  1. Install the Ripple RPM repository:

    Choose the appropriate RPM repository for the stability of releases you want:

    • stable for the latest production release (master branch)
    • unstable for pre-release builds (release branch)
    • nightly for experimental/development builds (develop branch)
    cat << REPOFILE | sudo tee /etc/yum.repos.d/ripple.repo
[ripple-stable]
name=XRP Ledger Packages
enabled=1
gpgcheck=0
repo_gpgcheck=1
baseurl=https://repos.ripple.com/repos/rippled-rpm/stable/
gpgkey=https://repos.ripple.com/repos/rippled-rpm/stable/repodata/repomd.xml.key
REPOFILE

    cat << REPOFILE | sudo tee /etc/yum.repos.d/ripple.repo
[ripple-unstable]
name=XRP Ledger Packages
enabled=1
gpgcheck=0
repo_gpgcheck=1
baseurl=https://repos.ripple.com/repos/rippled-rpm/unstable/
gpgkey=https://repos.ripple.com/repos/rippled-rpm/unstable/repodata/repomd.xml.key
REPOFILE

    cat << REPOFILE | sudo tee /etc/yum.repos.d/ripple.repo
[ripple-nightly]
name=XRP Ledger Packages
enabled=1
gpgcheck=0
repo_gpgcheck=1
baseurl=https://repos.ripple.com/repos/rippled-rpm/nightly/
gpgkey=https://repos.ripple.com/repos/rippled-rpm/nightly/repodata/repomd.xml.key
REPOFILE

    cat << REPOFILE | sudo tee /etc/yum.repos.d/ripple.repo
[xls20]
name=xls20
baseurl=https://repos.ripple.com/repos/rippled-rpm-test-mirror/xls20
enabled=1
gpgcheck=0
repo_gpgcheck=1
gpgkey=https://repos.ripple.com/repos/rippled-rpm-test-mirror/xls20/repodata/repomd.xml.key
REPOFILE

    • Fetch the latest repo updates:

      sudo yum -y update

    • Install the new rippled package:

      sudo yum install rippled

    • Reload systemd unit files:

      sudo systemctl daemon-reload

    • Configure the rippled service to start on boot:

      sudo systemctl enable rippled.service

    • Start the rippled service:

      sudo systemctl start rippled.service

    Next Steps

    It can take several minutes to sync with the rest of the XRP Ledger network, during which time the server outputs various warnings. For information about log messages, see Understanding Log Messages.

    You can use the rippled commandline interface to see if your server is synced with the network:

    /opt/ripple/bin/rippled server_info

    If the server_state in the response is full or proposing, then your server is fully synced to the network. Otherwise, you may need to wait longer. Fresh servers usually sync within 15 minutes; servers that already have ledger history stored can take longer.

    After your server has synchronized with the rest of the network, you have a fully functional XRP Ledger peer-to-peer server that you can use to submit transactions or get API access to the XRP Ledger. See Client Libraries or HTTP / WebSocket APIs for different ways to communicate with the server.

    If you use the XRP Ledger for your business or you want to contribute to the stability of the network, you should run one server as a validator. For information about validating servers and why you might want to run one, see Run rippled as a Validator.

    Having trouble getting your server started? See rippled Server Won't Start.

    Additional Configuration

    rippled should connect to the XRP Ledger with the default configuration. However, you can change your settings by editing the rippled.cfg file. For recommendations about configuration settings, see Capacity Planning.

    The recommended installation uses the config file /etc/opt/ripple/rippled.cfg by default. Other places you can put a config file include $HOME/.config/ripple/rippled.cfg (where $HOME is the home directory of the user running rippled), $HOME/.local/ripple/rippled.cfg, or the current working directory from where you start rippled.

    See the rippled GitHub repository for a description of all configuration options.

    You must restart rippled for any configuration changes to take effect:

    If you change the [debug_logfile] or [database_path] sections, you may need to grant ownership of the new configured path to the user you run rippled as.

    Updates

    You must update rippled regularly to remain synced with the rest of the XRP Ledger network. You can subscribe to the rippled Google Group to receive notifications of new rippled releases.

    The rippled package includes a script you can use to enable automatic updates on Linux. On other platforms, you must update manually.

    See Also